If you manage a commercial or multifamily building, you probably walk past the same facade every week. After a while, the brick stops registering. Small changes are easy to miss when you pass the wall every day. A joint has opened a little more since spring, a rust streak has formed under a window lintel, and a white bloom keeps coming back after cleaning. They are also often the first signs that water is getting into the building envelope.
Caught early, most can be handled as planned maintenance. Left through a few wet seasons, they can turn into a leak call from a top-floor tenant and an emergency repair bill. Use this building envelope inspection checklist on twice-yearly walkthroughs of commercial and multifamily properties in Greater Seattle. It helps you spot common warning signs, document the condition of each wall, plan repair budgets, and decide which findings need a professional assessment or building envelope repairs.
What This Building Envelope Inspection Checklist Covers
This building envelope inspection checklist covers commercial and multifamily masonry buildings, inspected twice a year from the ground, through windows, and indoors. It works through mortar joints, brick and stone, sealant, wall penetrations, lintels, sills, copings, flashing, and drainage, then checks inside for signs of water intrusion.
- Ground level: mortar joints, brick and stone face, grade and drainage
- Eye level to roofline: sealant joints, penetrations, lintels, sills, copings, and flashing
- Interior: top-floor and perimeter units, below-grade walls, and the tenant complaint log
- Record: two photos per finding, exact location, and a three-tier rating
When to Run This Inspection
Walk the building twice a year on a fixed schedule: in late summer or early fall, before the rains start, and in late spring, after freeze-thaw season is over.
In the Puget Sound, the wet season does most of the damage. Water soaks into open joints and failed sealant, and each freeze widens the gap. A defect found in September can be repaired before months of rain drive water through it. The same defect found in March has already let a full season of water into the wall. For building envelope maintenance, the pre-rain walk is the one that saves money.
The spring walk shows you the damage that winter did. Late spring through early fall is the working window for tuckpointing and joint repair in this climate, so anything it turns up can be scheduled the same season.
Three events call for an unscheduled walk:
- Windstorms: check copings, flashing, and anything anchored to the facade
- First heavy rain: check interiors and below-grade walls while the evidence is fresh
- Tenant water complaints: walk the exterior above and around the reported unit
On a calendar, each finding gets planned, priced, and approved before a top-floor tenant calls about water on the ceiling and a small repair becomes an emergency.
What You Need Before You Start
- A phone camera for every finding
- This checklist printed, or a notepad
- Binoculars or a zoom lens for upper floors
- Chalk or painter’s tape to mark locations
- A flashlight for closets, stairwells, and below-grade spaces
Everything on this checklist can be seen from the ground, from a window, or from inside the building. Do not go on the roof or up a ladder to do it.
Ground Level: What You Can See Up Close
Mortar Joints
Check the mortar between the bricks for erosion, cracking, and loose material.
- Pass: joints are intact, with a consistent profile and no visible gaps or crumbling.
- Fail: joints are deeply recessed, cracked, missing mortar, or shedding loose, sandy material.
Deteriorated joints can allow moisture into the wall. Check several areas on each side of the building, and photograph the worst spots so you can compare their condition during the next inspection.
Repairs may involve repointing the joints with mortar compatible with the original masonry. Mortar that is too hard for older, softer brick can contribute to cracking and spalling. If you cannot tell whether a crack runs through the brick or the joint, see how cracked bricks differ from failing mortar.
Brick and Stone Face
Check brick and stone surfaces for flaking, white deposits, and movement out of line with the wall.
- Pass: faces are intact, with no visible white deposits, and the wall appears flat when viewed along its length.
- Fail: flaking or missing faces, white crystalline deposits, or units that are displaced, bulging, or leaning out from the wall.
Spalling is the flaking or breaking away of a brick’s face. It can indicate trapped moisture and freeze-thaw damage. Record where it clusters, because damage beneath a sill, below deteriorated joints, or near a downspout can help identify the moisture source.
Efflorescence is a white crystalline deposit left as moisture evaporates from masonry. Record affected areas, especially deposits that return after cleaning. Preventing efflorescence starts with identifying and correcting the moisture source. A professional can determine whether masonry repairs or masonry waterproofing are appropriate.
Displaced or bulging masonry needs prompt professional assessment. From a safe location, look along the wall for sections that bow, lean, or project beyond surrounding units. These changes may indicate problems with the wall’s connections or support. An assessment can determine whether anchoring, seismic retrofitting, or another repair is needed.
Grade and Drainage
Check whether the ground and drainage system direct water away from the base of the building.
- Pass: the ground slopes away from the building, downspouts discharge away from the foundation, and no water collects against the wall.
- Fail: soil or planter beds cover the lower masonry, the lowest courses show splashback staining, downspouts discharge at the foundation, or water pools against the wall after rain.
Planters added after construction can raise soil against masonry and conceal moisture damage. Record these locations and each downspout outlet so future inspections cover the same areas. A walkthrough during or shortly after rain can reveal pooling that is easy to miss in dry weather.
Eye Level to Roofline: The Envelope’s Weak Points
Sealant Joints
Check control joints, expansion joints, and the perimeter of windows and doors for gaps or deteriorated sealant.
- Pass: sealant forms a continuous bead, remains flexible where accessible, and is bonded to both sides of the joint.
- Fail: sealant is cracked, hardened, missing, or pulling away from the masonry or frame.
Failed sealant around windows and other openings can provide a route for moisture. Inspect accessible joints up close and use binoculars for upper floors, looking for gaps or dark lines along the edges of the bead.
Repairs may involve removing deteriorated material and resealing the joints. Interior staining can also provide clues; compare those locations with the exterior warning signs of failing caulking.
Penetrations
Check where vents, conduit, signage anchors, light fixtures, and other attachments pass through the wall. Include holes left by removed equipment.
- Pass: seals around penetrations are intact, with no visible gaps, open holes, or staining below them.
- Fail: sealant is missing or cracked, holes remain open, or stains trail down from an opening.
Old anchor holes are easy to overlook. Removed signs, awnings, and satellite brackets can leave openings that collect water. Photograph each finding and note its location so it can be assessed and sealed with an appropriate material.
Lintels, Sills, and Copings
Check the steel lintels above openings, the window sills below them, and the coping stones along the top of the wall.
- Pass: no visible rust staining or cracking around lintels, intact sills that slope outward, and aligned copings with intact joints.
- Fail: rust staining or cracking around lintels, damaged sills, or open joints, displaced units, or missing sealant at copings.
Steel lintels can rust and expand, putting pressure on surrounding masonry. Record rust streaks, cracks, and displaced brick at each affected opening by floor and location.
Window sills should direct water away from the wall. Look for cracks, damaged drip edges, and staining beneath the sill that may indicate water running back toward the masonry.
Coping stones protect the top of the parapet from water entry. Use binoculars to look for open joints, shifted stones, and deteriorated sealant. Record visible concerns for professional assessment; concealed flashing beneath the coping cannot be checked from the ground.
Flashing and the Wall-to-Roof Transition
Use binoculars or a zoom lens to inspect visible flashing and the junction between the wall and roof.
- Pass: visible flashing appears secure and continuous, with no obvious gaps, lifted edges, or corrosion holes.
- Fail: flashing is loose, lifted, visibly deteriorated, or separated from adjoining surfaces.
Leaks at the roof-to-wall transition can be difficult to trace. A ground-level inspection may reveal visible damage, but it cannot confirm the condition of concealed flashing or connections.
Record questionable areas and compare them with any staining inside the top floor. When both occur in the same area, arrange a professional inspection with suitable access before defining the scope of envelope repair work.
Interior: What the Inside of the Wall Tells You
Top-Floor and Perimeter Units
Look for staining at the ceiling-wall junction, blistered paint on exterior walls, efflorescence on exposed interior masonry, and a musty smell in closed perimeter closets. Use the flashlight in closets and stairwells. Record each finding by unit number and wall so it can be matched to the exterior elevation.
Below Grade
Check basement and parking-level walls for damp patches, white mineral deposits, and active seepage within a day of a heavy rain. Compare what you find against the grade and drainage notes for the same elevation. A wet wall below a downspout that discharges at the foundation usually points to the cause.
The Tenant Complaint Log
The complaint log is inspection data. Two leak reports in the same stack across two years is a pattern, not two incidents. Read the log by stack and elevation as well as by date. Water can run inside the wall and surface several floors below where it entered, so the unit that calls is often not the unit with the problem. Left alone, those patterns carry the hidden cost of deferred masonry maintenance.
How to Document What You Find
Photograph every finding twice: one wide shot that places the condition on the building, then one close shot of the condition itself. The wide shot is what lets you find the same spot next year.
Record the location precisely. “North side” will not find a cracked joint two years from now. “North elevation, third floor, second window from the east corner” will. Use the same format on every walk.
Rate each finding on three tiers:
- Monitor at the next walk: stable, minor conditions with no water reaching the interior
- Budget for this cycle: active deterioration that will worsen through another wet season
- Address now: active leaks, out-of-plane brick, or displaced copings
Each entry in the record should hold the same fields:
| Field | What to record |
|---|---|
| Date | The date of the walk |
| Location | Elevation, floor, and bay or unit |
| Item | The checklist item, such as mortar joint or coping |
| Condition | What you saw, in plain words |
| Tier | Monitor, budget, or address now |
| Photos | Reference numbers for the wide and close shots |
Keep the same record year over year and shoot repeat findings from the same angle. A crack that has not moved in three years is a different problem from one that has doubled in a single winter, and only a dated series of photos shows which one you have.
A documented record with photos and dated comparisons is what gets a capital request approved. A verbal concern with nothing behind it gets deferred to next year.
What a Professional Inspection Adds
A twice-yearly walk catches most of what a building shows from the outside. These are the things it cannot do from the ground:
- Parapet access: reaching copings, flashing, and the roof edge by hand
- Test sections: opening a small area of wall to see the cavity behind it
- Structural judgment: telling structural cracking apart from cosmetic cracking
- Cavity and flashing: confirming whether water is getting past the face
- Repair sequence: producing a scoped, priced order of work ownership can approve
Our proactive inspection service picks up where your walk stops, and it is built for property managers. Union-trained masons walk the building with access to the parts you could only see through binoculars, document every finding with photographs, and deliver prioritized recommendations with budget estimates formatted for a capital plan or an owner presentation.
Where mortar is failing, we check the original mortar composition before specifying a repair mix, and we scope tuckpointing wall by wall according to how deep the joints have failed. When the findings call for building envelope repairs, the report gives that work a documented starting point.
A Twice-Yearly Walk Turns Warning Signs Into a Budget Line
Many envelope problems show up on the face of the wall before they reach a tenant’s unit. Walk the building before the rains and again in late spring, rate every finding on the same three tiers, and keep the photos and locations in one record year over year. That record turns scattered warning signs into repairs you can plan, price, and get approved on your own schedule.
Know What You Are Looking At Before It Becomes a Repair
If your own walk turned up findings you want a second opinion on, our union-trained masons will inspect them with access and photographic documentation. You will get prioritized recommendations with budget estimates you can take to ownership. Call (206) 696-6998 or request a walkthrough.
Frequently Asked Questions
How often should a commercial building envelope be inspected?
A commercial building envelope should get a self-run building envelope inspection twice a year: in late summer or early fall before the rains, and in late spring after freeze-thaw season. Bring in a professional after any water-intrusion event, and whenever the walk turns up a finding you cannot judge from the ground, such as out-of-plane brick or questionable flashing.
What does a building envelope inspection cover?
A visual building envelope inspection covers the walls, mortar joints, sealants, penetrations, lintels, copings, flashing, and the roof-to-wall transition. Building envelope testing, such as water testing or infrared, goes further and shows where water is moving behind the face. Testing is usually added when a visual inspection finds a problem it cannot trace.
What would fail a building envelope inspection?
Open or receding mortar joints, sealant pulled away from one face, rust staining under steel lintels, open coping joints, and active seepage below grade would each fail this checklist. Bulging or out-of-plane brick fails it outright and calls for a professional the same week. Each one is a condition failure to plan maintenance around.
Can a property manager inspect the building envelope without a contractor?
Yes, for every observable condition on this checklist. That is the part of masonry oversight in property management a manager can own with a camera, binoculars, and a consistent record. No, for anything that requires parapet or roof-edge access, opening the wall assembly, or a judgment about whether cracking is structural. Those calls need a mason on site.
What does a building envelope inspection cost in Seattle?
A quote for your building is the accurate number, set by its size, the number of elevations, access to the upper walls and parapet, and whether testing is included. A documented record from your own walks helps any inspector scope the work more precisely.
What is the difference between a building envelope inspection and a building envelope assessment?
An inspection is the recurring visual check this checklist describes, run on a schedule by whoever manages the building. A building envelope assessment is separate professional work with its own scope.

